Layra
LAYRA is EMBRA’s sleek, one-piece winged bra designed for effortless lift and invisible contour. Crafted from featherlight silicone with sculpted side wings, it glides along your curves and provides secure comfort for 4–6 hours of wear. With SkinBond™ Solid Silicone Adhesive, it stays in place through any occasion—strapless, backless, or bold.
Wear & Care Guide
To make sure your EMBRA Invisibra fits like a second skin and stays perfectly in place, you’ll need to prep your twinnies with a little extra love.
Cleanse with Care for a Perfect Stick
Even if your skin looks clean, your body naturally sheds dead skin cells—especially around the center curve area (commonly known as the areola) of your twinnies. These skin particles may transfer to the adhesive during wear, dulling its grip or causing light surface staining.
This is totally normal and easily fixable.
To avoid it:
- Gently wash your twinnies with mild soap and water, paying special attention to the center curve area (areola) where the cups will sit and clasp. Dry completely—no dampness or product residue.
- Avoid touching the adhesive until the bra is fully applied.
Why it matters: EMBRA’s skin-friendly silicone may cling to skin debris if not properly cleaned. Don’t worry—it can be refreshed using Rinsee Gentle Liquid Soap by EMBRA, specially made to preserve the adhesive.
DO NOT apply before wearing:
- Moisturizers
- Oils or serums
- Powders, sprays, or deodorants
- Perfume
These act as a barrier and prevent the bra from sticking properly. Clean, dry skin = lasting hold and seamless shape.
One-piece winged bra with seamless glide-on fit and cat-eye contour.
Peel the Film
Gently peel off the protective plastic film from the adhesive side of LAYRA. Hold only the wing edges (non-sticky zones) to avoid touching the adhesive.Apply One Side First
Starting with one wing, gently hug the outer side of your twinnie, then glide the wing inward toward the center, slightly upward. The motion should contour the side of your twinnie, lifting it softly.Press to Secure
Once in place, press firmly across the wing and center for about 10 seconds to ensure full contact and adhesion.Repeat on the Other Side
Apply the opposite side using the same side-to-center, slightly upward glide. Adjust both sides to achieve your desired lift and symmetry.Tap & Smooth
Finish by lightly tapping across the surface, especially the edges, to smooth out air gaps and complete the invisible finish.
Extend its life. Keep it flawless. Reuse with confidence.p>
Your EMBRA Invisibra — whether NAYA, FEYA, or LAYRA — is made to last through 20+ wears (or more!) with the right care. Gentle maintenance will help preserve the adhesive, shape, and comfort of your bra for weeks, even months.
After Every Wear, Follow These Steps:
Peel Off Gently
Start by slowly and gently removing each cup sideways, beginning from the outer wing or side of the cup, peeling inward toward the center. Avoid pulling too quickly or in a downward motion, as this can strain both your skin and the adhesive. Use a soft, steady motion for a clean, damage-free removal.Wash with Care
Use lukewarm water and a soft, foaming soap — or ideally, Rinsee Gentle Liquid Soap by EMBRA, specially formulated to protect our skin-safe adhesive.- Lather gently using only your fingertips
- Do not rub, scrub, or use nails, cloths, or brushes
- Avoid applying direct pressure to the adhesive
💡 Pro Tip: Even if your bra looks clean, your skin naturally sheds oils and particles.
Always clean your Invisibra after 1–2 wears to maintain maximum stickiness and hygiene.
Rinse Thoroughly
Rinse under lukewarm water until all soap is removed. The surface should feel clean and residue-free.Air Dry Flat
Lay the bra adhesive-side up on a clean, flat surface. Let it air dry completely at room temperature.Never use:
- Towels or tissues
- Hairdryers or blowers
- Direct sunlight or heat
Reapply the Protective Film
Once fully dry, reapply the original plastic film to protect the adhesive from dust, lint, or particles.Store It Properly
Slip your Invisibra back into the EMBRA Velvet Pouch, or use the Zippy Silicone Travel Case if you're on the move. Store in a cool, dry place, away from direct sunlight or humidity.
When You Care, It Stays With You
With the right routine, your EMBRA Invisibra will support your twinnies for dozens of wears—invisibly, comfortably, and confidently. Because at EMBRA… You don’t just wear confidence. You care for it.We currently ship to the United Arab Emirates only.
Dubai/Sharjah/Ajman
2-3 Days
Free delivery for orders AED 350 and above.
AED 18 shipping fee for orders below AED 350.
Abu Dhabi/Ras Al Khaimah/Al Ain/Umm Al Quwain
3-4 Days
Free delivery for orders AED 350 and above.
AED 18 shipping fee for orders below AED 350.
Skinsilk Invisible Bra
"Layra"
Float On. Stick Strong.
Meet Layra!
LAYRA is EMBRA’s sleek, one-piece winged bra designed for effortless lift and invisible contour. Crafted from featherlight silicone with sculpted side wings, it glides along your curves and provides secure comfort for 4–6 hours of wear.
With SkinBond™ Solid Silicone Adhesive, it stays in place through any occasion—strapless, backless, or bold.
- Winged Cat-Eye Shape for lift and side contour
- Featherlight Silicone Construction with ultra-thin 0.05 cm edges
- Matte Surface for a non-reflective, seamless look
- Sweatproof & Waterproof for up to 6 hours
- One-Piece Design ensures no lines or gaps
- Reusable up to 30+ short wears with care
